This is a Digital File Download for a DIY 3D Printable Model - Not A Physical (Tangible) Item
PLEASE VERIFY YOUR FILE BEFORE PRINTING, CURRENT FILE IS: M1_MandoGauntlets-11-19Update.zip
IF YOU DO NOT HAVE THIS FIILE, AND CANNOT ACCESS VIA ETSY PLEASE MESSAGE US.
VISIT OUR WEBSITE MAKERBAK3D.COM FOR THE MOST RECENT HARDWARE LIST! (LINK AT TOP OF HOME PAGE)
LAST MODEL UPDATE 11/14/19 - Please re-download your files to get the new improvements. Better fit, improved hinges & accessories.
- Built In Hinge System (easy on/off without help!)
- Rocket Dart Gun (left gauntlet)
- Port for brass hose connector (left gauntlet, brass hose connector not included in digital file.)
- Attenuator (left gauntlet)
- Emitter (left gauntlet)
- Heat Sink (left gauntlet)
- Button Panel (left gauntlet)
- Power Coupler with rear hole inset for hose connector (right gauntlet, hose connector not included in digital file.)
- Whipcord with rear hole inset for hose connector (right gauntlet)
- Darts designed to be reinforced with steel rods and seated in brass tubing (right gauntlet, steel rods and brass tubing not included in digital file..)
- Control Knobs (right gauntlet)
SIZE: Left Gauntlet 248mm overall exterior length; approximately 77mm wide x 63mm high front opening; approximately 100mm wide x 100mm high rear opening.
Right Gauntlet 231mm overall length; approximately 77mm wide x 63mm high front opening; approximately 100mm wide x 100mm high rear opening; 120mm high exterior profile.
Lengths are different due to button panel on Left Gauntlet.
QUALITY CHECKED IN SIMPLIFY 3D AND TEST PRINTED: We print all the parts in our 3D MODEL FILES (STL's) to ensure you get a quality 3D Printable Model File and a functional part! In most cases, the DIY 3D Model Files that we sell are the VERY SAME FILES WE USE TO MAKE THE PHYSICAL ITEM.
3D PRINTING THE M1 MANDO GAUNTLET SET:
The Gauntlets are designed to be printed in 2 pieces and assembled with the additional hardware noted below. The Gauntlets can be printed one at a time on a small 3D Printer, such as an Ender 3 (220x220x250mm), or print both on a large format printer (300x300x400mm).
We print our Mandalorian Helmets & Armor with FilaCube PLA 2 at 0.2 mm layer height, with 5 perimeters/top & bottom layers, and 20% infill.
ADDITIONAL HARDWARE REQUIRED: You will need the following hardware (or similar) to complete the gauntlets build:
9x M3 x .05 x 12mm screws
9x 3mm washers
2x 2mm x 300mm stainless steel rods. (Gauntlet hinges)
4x 1mm x 50mm stainless steel rod (internal support for darts)
Please download the Hardware Links pdf file for links to hardware online.
You can print both Gauntlets at the same time on a large format printer (300x300x400mm).
Included with the 3D Printable Model File is a detailed printing and assembly document that should explain everything clearly. However, if there's anything you're not certain about please feel free to contact us. We want you to be happy with your purchase, and will do whatever possible on our end to ensure you get a successful print!
Some cleanup, sanding or filing may be required to get everything to fit properly. We've tested the tolerances and they do work, but if you run into difficulty, or have questions, please contact us. We're happy to help, and in an extreme case where something is just not working, I will provide revised files at no cost to you.
WHERE TO GET YOUR FILES: After purchasing your files are available for download anytime once payment has been confirmed. You can find your Digital Download purchases under your Profile and Purchases.
PLEASE TAG US ON SOCIAL MEDIA SO WE CAN SEE IT IN THE WILD! And we'd be ever so grateful if you'd credit us with the 3D Model File used for your cosplay creation - @makerbak3d on Instagram, Twitter & Facebook. Thank you!
FOR INDIVIDUAL PERSONAL USE ONLY. PLEASE DO NOT SHARE OR DISTRIBUTE FILES.
NOT FOR USE IN ANY COMMERCIAL ASPECT! DO NOT DUPLICATE, CAST, MASS PRODUCE, OR SELL THE FILE OR THE PHYSICAL OBJECT FOR PROFIT.
THIS IS THE WAY.
This is not an official licensed product and is only considered fan art protected under the fair-use act.
Not associated with LUCASFILM LTD. ™ or any LFL Ltd. ™ Film or Franchise. "Star Wars" is a registered trademark of LucasFilm Ltd. The Star Wars logo, characters, prop designs and names © LucasFilm Ltd. This document and related sites/products is not sponsored or endorsed by LucasFilm Ltd. or any of its affiliates. All © and ™ are property of their respected owners and are used here for comparative or descriptive purposes only.
Your files will be available to download once payment is confirmed.
Request a cancellation within: 24 hours of purchase
But please contact me if you have any problems with your order.
Unless otherwise noted, helmets and armor are made to fit most males from 5'7" to 6'6". Some listings do have specific sizes noted, please take a moment to read them where included. Most items can be scaled if you feel they may not fit. There may or not be an additional charge depending on the item and material usage change. Please include your measurements with your order, or message us with any questions you may have before placing an order.
We are located in the U.S. and observe all National Holidays. If your order is due to ship on a National Holiday, when the U.S. Postal Service is closed, your ship date will be delayed until the next business day.
No, our Unfinished Kits are raw 3D prints, right off the printer. We do basic support removal, and include finishing recommendations. All you'll need is some sandpaper in several grits, primer, possibly some putty, and some elbow grease. Yes, you can sand 3D prints, just don't over do it and sand correctly. Move in circular motions when possible and keep moving; don't sand in one spot too long or you could heat the area and damage your part. However, the majority of our Armor plates are 5mm thick, you'd have to go hard at it to damage them by sanding! If you have any questions, just contact us we're happy to share our process.
No, finishing the interior of your helmet is easily done with readily available felt and/or foam. You'll need to add padding to specific areas to make the helmet sit correctly on your head, so it's best to do it yourself. We promise it's really not hard at all! There are plenty of videos on YouTube to show you how to go about padding out the interior of your MakerBak3D helmet. ;-)
Yes, it is! We just had a customer have his helmet inspected by an Idaho Regional MMCC Rep, who said it looked really nice. :-)
We do not accept returns because each item is made to order, just for you. If you have any problems with your order once received, please contact us so we can make it right.
Our listings include size information for each helmet. Generally, Male character helmets fit up to 24" diameter heads, and Female character helmets fit up to 23.5" heads. We measure around the forehead, and that will leave room between your nose and the T-Visor in our helmets. You'll also have enough room for your interior finish/padding, and any electronics/fans you may want to install.
Packages are sent to the address entered at the time of the order only, and we're not responsible for packages delivered due to incorrect address entry. ETSY PROTECTION DOES NOT ALLOW US TO CHANGE BUYER'S SHIPPING ADDRESS ENTERED AT THE TIME OF PURCHASE.
How to update your shipping address on Etsy.com:
1. Click the "Your Account" icon (top right).
2. Click "Purchases and Reviews".
3. To the right of your order, you’ll see either "Shipped" or "Not Shipped".
If your item is Not Shipped yet:
1. Contact us to cancel your order.
2. Update your shipping address in your Etsy profile.
3. Re-Order your items with the correct shipping address in your Profile.
If your item has Shipped, contact your Post Office and us immediately. Be Proactive!
May 2, 2020
Very nice files! Thanks!